1995 Jeep Wrangler

Sport Utility

350 v8

1j4fy19p6sp204556

Clear

GAS

NO RESERVE... So this is a 95 jeep yj with a cj7 front end on it... But very few people could tell the difference.  This has been my long time daily driver turned project turned I bought a house and a boat and it's time to say goodbye  I have frame off restored on a budget, not for a showroom or trailer queen finish . This was always a project for me  and now is a solid base as a daily driver or for further restoration or even a off-road vehicle Body - 95 tub cj7 front end  Body needs some work but is mostly rust free and straight ... No rot in the tub or floor boards  Painted with rustoleum satin paint that was thinned and sprayed through a hvlp gun New windshield frame and glass  I do not have a tailgate and will need some modification to put one on I have a piece of wood propped up and this works fine for me The tub is bed lined New body mounts  Tail lights are 4" flush mount trailer lights  New black denim soft top and new black denim front bucket seats. I have no rear seat . Gauges are omega kustom gauges  Also has new aftermarket wiring harness  with new connectors  Frame is solid and painted with epoxy paint  4" rough country suspension  33" general grabber at2s black aluminum rims  ... This power plant is MEAN Engine is a 5.7 v8 gm performance zz4 short block 4 bolt mains hypereutecic pistons 64 Cc HO heads  with stainless 2.02/1.6 valves, new lifters and pushrods  Comp cams 256 cam in it nice lope but still very streetable as a daily driver.  Around 350hp 400ft/lbs torque Aluminum intake, new Holley 600cfm vacuum secondary (also for a little more streetability, if you put a 650 double pumper on this thing. It would be scary ) larger jets and tuned with a wideband o2 sensor new accell hei vacuum advance distributor   4l60e automatic transmission with a B&m shift kit  2200 stall converter and TCI ez-tcu trans controller . (Which you can change settings from street to  strip settings, shift points / firmness etc.. This comes with a handheld module that plugs into the lighter socket and adjust in the car ) Np241 transfer case with clocking ring with jb conversions shorty slip yoke eliminator kit custom double cv rear driveshaft.  This motor was rebuilt last year and has less then 50 miles on it.  Aluminum radiator and electric fan.  Lokar tall shifter and I have a craftsman wrench for the 4wd shifter .  Shorty headers and 2.5" mandrel exhaust 2 into 1 high flow cat, flow master hush power 2 muffler..  This jeep is  mostly done it runs and drives great.   If I were to use this as a daily driver the only thing it really needs is a  tailpipe. And the overflow resivoir bolted to the inner fender  If you plan on needing or wanting 4wd here's what it needs  A front drive shaft made (I had a custom rear shaft made by tattons driveshaft they have an ebay store and did a great job and are affordable with quick turn around) The front Dana 30 axle has a vacuum actuator that needs to be activated when put into 4wd . This can be done number of ways...  There's a company called 4x4 posi lok who makes a kit for $159 that replaces the vacuum actuator with a cable. This is the most common in the off-road world  I had planned on running a simple brass valve  on the  dash with air tubing from the manifold to the  axle.  That you would open and close  when u wanted to go into 4wd. This would be much simpler and much cheaper  At any rate I have a lot more money in this thing then I'm asking.  And your getting a Solid vehicle just needs some fit and finish. I have extra parts to go with it  such as extra headlights and turn signal lenses , I have the windshield gaskets  in case you chose to repaint. I have a mesh Bimini top I have a soundbar I have side mirrors that bolted to the windshield frame for when you take the doors off   This is being sold as is  PayPal or cash only  Clean sc title in  my name  NO RESERVE  BUY IT NOW not a reserve price  Don't ask me what do I have for it or what's my bottom line ... Just bid  Also for sale locally and can be ended  at  any time  Serious bidders only, please do not bid if you are unsure of anything or have any questions about the vehicle Please ask questions , please come see the jeep and I'll be happy to take you for a ride . Call text or message me on here  Mike 443-848-6442 FYI the jeep is currently together and running , the pics of it apart are just to show you  some of the work done .