1967 Ford Mustang

coupe Coupe

-

-

7r01c185381

Gasoline

My husband and I purchased this mustang from a very close friend who was the original Owner. We have put Thousands of dollars in parts alone on her. We certainly didn't spare anything. The car has been completely custom done. Clear Title- Title in Hand- Here is a List of what we have done: (OVER $19,500 in PARTS ALONE) Complete interior was sand blasted and sealed and then paintedI will have a box of miscelaneous parts : IE - Left over window lace- hardware, weatherstripping, brackets- Complete Brake calipers that are brand new for the Front Suspension, stering column bracket, emergency brake brackets etc- all in a seperate box for the new owner of this vehicle. Correct paint finish added to the dash area after it was prepped with the subdeud Black Automotive paint that cost 160.00 a Quart- we used 1 gallons($640)- The primer cost us 80.00 a quart- we used 5 quarts ($400)Underbody was primed and we completely under coated the underbelly with 3m Rubberized undercoat- $9.00 a can - we used 12 cans($108)New Complete doors on both sides- 1100.00Complete weather strip kit for all windows and doors to include belt lines, and rubber door moldings- 280Windows were sent out to get completly rechromed 550.00Windows were then resealed with all new weather stripping and seals- 275.00A Complete wiring harness was installed and all wires were upgraded- Fuse box included with all fuses and regulators. All Wires are marked for their location and routed to their correct locations. Kwik wire is the manufacturer of the wire harness. This harness was CUSTOMIZED as we wanted to ensure thicker wires for all the power we were going to run through her- 895.002 completely new Wing window frames- 600.00One piece floor pan Completely installed/ welded and rivited and completey sealed 1400We added a complete fire and sound proof barrier throughout the entire can and used aluminum tape to water proof it. 600.00 Rear Deck In Black Hard Molded Plastic with Complete Audio with rear brake light and custom emblem mounted, Pioneer speakers 800Rear Truck to Cab has a Complete custom door skin that has a sound barrier sheathing on rear and stainless screws hold it in place- 120All new door Hinges and Latches- 235All window mechanisims were completely restored and all roll pins Custom made for a tighter fit than the after market could supply- 580.00Complete New Gas Tank and filler neck completely sealed -285New Eleanor Truck Lid and Side pieces-785.00New Trunk Latch and hardwareNew tail light Lens and bezels 345New rear light sequentials completely installed and appropriate installation instructions included to install it into the wiring harness- 185.00Rear back up lights are Made in USA and New- 85.00New rear valance- 65The entire inside Vinyl top is installed with all new Rods and interior dome lights- 385New Sunvisors on Both sides and Rear view Mirror bracket using all polished material -212The suspenion is a COMPLETE TCI FRONT suspension! I paid 3800.00 alone just for this- Comes with Complete rack and pinion steering rack, drilled and slotted rotors, Adjustable Polished shocks and so much more. My husband is a Professional Mechanic and together we welded this unit in. We cut out the old brackets etc and completly sanded them all down to add this unit. The shock towers were eliminated as well which gave us much more room in the engine bay.I added a Sway bar and added new brackets that were also welded in. 285The Entire frame rails were blasted and treated 125.00The interior Boasts interior kick panels with Pioner speakers as well- 385All the exterior rust was treatedCowel was completely sealed and welded where neededHeater Box and Plenium and resistor and Heater control cables are all installed , Vent and heater hoses included 580New Wiper motor and arms installed 195The Engine compartment was completely sand blasted and sanded and Primed using Eastwood Paints and Now has a Candy shine- It was Ceremic High Temp Engine Paint in Gloss Black- This stuff is induestructable! Total paint cost 566.00I did spray paint the exterior car because I was tired of the calico paint- I did sand down the passenger rear and I noted there was a small bondo patch- The original owner hit a shopping cart in a parking lot and had it bondoed before her mom ever saw it. There is small pin holes in rear quarter panel and I sanded them and added por 15 on any rust spot. The moldings for all windows and rails is in the trunk they are in good condition and will need to be polished as they are originalsI paid 2500.00 for the carI know I am forgetting lots of things! Some items I do not have any idea what I paid so no value was established for those items- I have so many parts for this car also going up for auction. I have all the parts to put it together again But No Time. Hubby was injured in Iraq and then I had a Severe Knee injury and that left us with a very tough decision. We have spent countless hours and are certainly proud of this accomplishment but we no longer have the time or physical capacity, to complete her. She sits in a heated garage and we would like to find someone who can appreciate the quality of the work, and time it took to get her here. I will have all the gauges and seats (completely restored with carbon Fiber) Door panels, ceremic exhaust, billet mirrors, shelby scoops etc and all the trimmings sold in seperate auctions THE FINE PRINT: Buyer Pays shipping- Cash, paypal - Upon end of aution 20% down, remaining due within 7 days of auction end. Sold as is where is, with no warranty expressed or implied.