1999 Honda CR

Too many rides in the garage, so this ones up for sale 1999 CR250 Chassis w/ 1991 CR500 motor Frame work done by aircraft certified welder Motor was just done by Glenn at GSS less than 1.5 hours ago -motor was treated to the full meal deal - rated for 68-73hp depending on state of tune - per Glenn -Motor received his latest race porting, carb and manifold were also matched to his work as was the exhaust manifold, also match to pipe. ****this is a holeshot monster, eat your 4-stroke friends alive with this bike! Bike has 13.2 hours on the meter since it's build spring 08, every part needed refreshed was replaced. Devol racing did the forks and shock, sprung for 200-240lb rider. I have approx. $7000 in the bike as it sits. Bike is ready for a new rider, comes with bill of sale.On Dec-15-10 at 11:14:11 PST, seller added the following information: Too many rides in the garage, so this ones up for sale 1999 CR250 Chassis w/ 1991 CR500 motor Frame work done by aircraft certified welder Motor was just done by Glenn at GSS less than 1.5 hours ago -motor was treated to the full meal deal - rated for 68-73hp depending on state of tune - per Glenn -Motor received his latest race porting, carb and manifold were also matched to his work as was the exhaust manifold, also match to pipe. ****this is a holeshot monster, eat your 4-stroke friends alive with this bike! Bike has 13.2 hours on the meter since it's build spring 08, every part needed refreshed was replaced. Devol racing did the forks and shock, sprung for 200-240lb rider. I have approx. $7000 in the bike as it sits. Bike is ready for a new rider, comes with bill of sale. Shipping cost is at buyers expense. I will take the bike to Forward Air for shipping if you would like to use them, or I have a contact on the west coast that ships reasonably $200-$300 to CA, OR, AZ, etc.On Dec-16-10 at 10:45:03 PST, seller added the following information: Motor work by GSS was $1200 pluse $200 for assymbly of the motor = $1400 on the motor last spring - run for 1.5 hours since fresh Aluminum frame conversion parts run $400 for the set for the motor mount bits and pieces to fit the motor in the frame plus $200 for welding = $600 on the frame conversion Custom Sudco 41.5mm carb(not stock) with GSS mods = $300 Nothing was done cheap on this build down to the custom graphics, everything was replaced or refurbished on the build - bike is ready for crushing your 4 stroke bros.On Dec-17-10 at 06:47:00 PST, seller added the following information: This bike is every bit as nice as the other two that are for sale at this time. No expenses spared on this build, and it has the MONSTER motor to boot. 73 horsepower - no bull. Research GSS raceporting in Palmdale CA to see his work. World recognized master of the CR500 motor. Bike pulls very hard right off the bottom and revs much higher than than a standard motor thanks to Glenn.On Jan-10-11 at 10:46:03 PST, seller added the following information: Bike will sell - Reserve Met!!!!On Jan-10-11 at 10:48:05 PST, seller added the following information: This bike is every bit as nice as the 5000-6000 dollar ones that have just sold - only this one has a MONSTER motorOn Jan-12-11 at 18:58:46 PST, seller added the following information: FORWARD AIR is a reputable and reasonable transporter I have used many times - Get a quote from them for transport dock to dock -- Seattle to your destination. You will need the medium container for this bike. Buyer is responsible for transport costs. I will get the bike to forward air in Seattle for you. On Jan-13-11 at 16:19:52 PST, seller added the following information: With the exception of the welded in parts everything parts wise is available at your Honda Dealer - chassis(everything but the motor)1999 CR250, motor 1991 CR500 - easy parts access.