1947 Willys

Convertible

8 - Cyl.

Automatic

123333

Gasoline

Engine: Small block Chevy, .060 over 4 bolt main, 360 cubic inches. Mallory Unilite electronic ignition, Mallory Promaster coil, Edelbrock 750 CFM carburetor, Edelbrock aluminum intake, B&M air cleaner, Crane musclecar 350/350 hydraulic camshaft, melling high volume oil pump, SRE high torque mini starter, marine aluminum 8 quart oil pan, aluminum Mickey Thompson valve covers, Griffin aluminum radiator, aluminum high volume water pump, ceramic coated fenderwell headers, & 2 ½” turbo mufflers. Transmission: 1970 Chevy Turbo-hydramatic 400 3 speed automatic. Trans was disassembled, boiled, and rebuilt with: new steels, new clutches, new band, new gaskets, and new seals. Valve body has a B&M trans-pak shift kit & adjustable vacuum modulator. Torque convertor is a 10”. Trans temperature is maintained via a ‘Keep Cool’ frame mounted trans cooler. Trans is shifted via a B&M Pro-Stick shifter with reverse lock-out and rear cable conversion. Transfer-case: Dana 20 twin-stick. Transfer Case was disassembled, boiled, and rebuilt with new gaskets, new seals, & new bearings. Shifter ‘lock-out’ detent was removed to achieve low range in 2 wheel drive. Rear Axle: Dana 44. Axle was disassembled, boiled, and completely rebuilt with new gaskets, seals, and bearings. Axle has 30 spline one piece axle shafts, new ring and pinion gears (4.27), new spring pads, new u-bolts, freshly turned drums (11”), new shoes/spring kits/wheel cylinders, new brake lines, and rear cover. Front Axle: Dana 25. Axle was disassembled, boiled, and completely rebuilt with new gaskets, seals, and bearings. Axle has 4.27 ring and pinion gears, new spring pads, new u-bolts, freshly turned drums (11”), new shoes/spring kits/wheel cylinders, new stainless braided flexible brake lines, new closed-knuckle seals, and ‘Warn’ locking hubs. Chassis: Custom built 2” x 3” tube frame with: frame mounted 8-point roll cage, heavy duty spring perches, military-wrap springs, heavy duty shackles and shackle bolts (w/ greasable zerks), heavy duty shock absorbers, removable transmission cross-member, heavy duty motor mounts, tube brush bar & bumper, and GM Power steering (Saginaw box, 4.25 turns lock to lock). General: Fiberglass body and fenders, original windshield & grill shell. Wilwood aluminum swing pedal assembly & brake master cylinder. Offenhauser throttle linkage. Quick disconnect steering wheel. Holley high-volume electric fuel pump. Holley high pressure fuel regulator. Fram high-volume fuel filter. ½” aluminum fuel line. Heavy Duty battery cables. Southwest speed battery box. Moroso battery disconnect. Diamond plate dashboard with grab bar. Autogauge gauges. ‘KC Daylighter’ headlights. Wheels are 15” X 10” Ansen aluminum slots. Tires are 33 X 12.50 X 15. They don’t appear to have been used much as they have a ton of tread. All the gauges (speedometer/odometer, oil pressure, voltmeter, & temperature) work. All lights (headlights, tail lights, brake lights, gauge lights) work. Seats are fully adjustable high back buckets, and are fairly comfortable. The wiper motor is new, but has never been hooked up. The willys runs, drives, handles, and stops good. The 10” torque convertor seems to stall too high, if I kept it, I would replace it with a stock 12” convertor. The paint is not perfect, and there are a few holes that are an eyesore (hole for an antennae & a hole for a gas tank filler tube…see pics). The windshield frame has some rust (see pics). Willys also comes with 4 KC Daylighters, a 2 sets of 3” seat belts, steel diamond plate rocker supports, and a steel diamond plate rear surround (see pictures). Please ask any and all questions. Thanks for looking, DougOn Aug-11-10 at 12:18:07 PDT, seller added the following information: while looking at the listing i noticed a few mistakes i made...two of the pictures did not load (see attached). the front corners of the rear inner fenderwells were cut/relieved to allow the seats to be mounted further back (for additional leg room). i have the pieces, but they have not been glassed back in. also, the roll cage is 10 points...not 8. and lastly, when i started it up to move it into the yard for pictures the starter seemed weak. it could be that the starter needs to be replaced, or simply the battery needs to be charged/replaced from sitting so long. i've lowered the reserve. if the reserve is still not met at the end of the auction, i will work with the high bidder (if interested) on the price. if you win the auction and do not feel the willys is exactly as described when you see it in person, you will not be obligated to buy it. thanks again for your questions & interest, doug