1965 Chevrolet Other Pickups

Custom Pickup Truck

350 4-Bolt

Automatic

Rebuilt, Rebuildable & Reconstructed

SELLING for you to finish or PART OUT- There is at least $4,000 in parts if you want to go that route. 1965 California (I have plates) and clear title- Chevy C/K 10 For Sale Low- No Reserve – I am moving and motivated to sell. Start price will $500.00 and will sell at whatever price. I have over $6,000.00 tied up in it. Buyer is responsible for picking it up or arranging all shipping. $250.00 Paypal down payment within 24 hours- the balance due withing 5 days by USPS money order sent priority mail, cash if you are in-state. There are at least 10 companies that sell EVERY single PART nut bolt glass -Everything. I have all the catalogs to go with it. Partial body off Restoration re-assembled with body on. The frame along with other chassis and body parts have been sand blasted and then painted with a (Southern Urethane) 2 part Epoxy Urethane Black satin primer and finish chassis only. Brakes need everything but I priced out at Car Quest at around $250.00 drums front and rear. Needs most new brake lines. The cab, front end sheet metal including inner fenders, Grill, Headlight holders,Radiator Supports are installed with all new correct urethane or rubber mounts and shims/ Tail gate and many small parts are also blasted and primed. No bumpers. The rockers need replacement but I do have those full patch panels, I do have door fix patches/panels if needed but doors look pretty solid. Drivers side needs floor fix patches/ panels, and the other side need minimal floor work. I piece of sheet metal needs to be fabricated or formed to finish hump on the floor that was missing. No Glass I have the the original mint condition aluminum large trim pieces that are behind the side windows that say CUSTOM – they are worth $200.00 on Ebay. The bed is removed in pieces and has virtually no rust but has some dents and needs to be stripped – The front box panel needs to be replaced, it is bolted in and aftermarket ones are cheap or fix the one with it. I have a the bed cross-braces but they need blasting as well- The original super heavy tail-gait is in great shape and has been blasted and has one coats of epoxy primer on it. There are no fenders although I have repair panels- The old ones were beyond my scope of fixing and believed after market ones would be more cost effective. About $400.00 for the pair if you go to the right place or get used up, these are notorious for rotting out. There is no glass that survived removal or was bad, and no gaskets for glass or doors- All easily available. Has a completely dressed (chrome) 6 year old 350-265HP 4-Bolt main GM crate Truck motor with a completely rebuilt 750 Rochester Quadrajet by the “Carburetter Man”, New Pro-line Billet HEI ignition, New 2-1/2 inch Corvette Ram Horn manifolds, New 8mm wires, New water pump, New mechanical fuel pump that is partially plumbed, New Flex fan and radiator, New starter, New Alternator, New flex plate, New standard Torque converter, New battery, New battery tray, New mandrel bent drops and 2 Thrush Turbo Mufflers. New hood hinges Used but inspected tuned and plumed 350 turbo hydramatic with updated cross-member. Brand new Drive Line including hanger bearing by – Clutch and U Joint Specialists - IT RUNS I CAN START IT FOR YOU- No exhaust just the drop pipe from the manifolds. 2 original solid doors with new hinges, and 2 other extra doors primed. There is no gas tank- The behind the seat tank is gone, the seat is gone. Inexpensive relocation frame tank required for between frame. No air, No power steering, heating and parts along with wiring harness and other miscellaneous parts are boxed up along with other miscellaneous pieces and parts. There are at least 10 companies that supply every part. SOLD AS IS Ask questions....I would part out at this point but don't have time.