1970 Ford P-350

U/K

4.9L 4917CC 300Cu. In. l6 GAS OHV Naturally Aspira

Manual

p35avj44267

Clear

GAS

Selling my most favored vehicle ever...... 1970 P350 Aluminum Step Van 4.9L 300ci I6 All aluminum body will never rust! I had this truck for about two years now, I have probably put 500 miles on it. All the doors and locks work great, windows wind down good but are stiff going up. The body is very straight, with only a small bondo spot on the front corners (thats the pink in the pictures)Transmisison is a 4speed manual, the first is really low. It does around 60mph on the highway though! Shortly after I bought it I had a local garage install the engine from a late 80's ford f150, it has around 80,000 original miles, it has new oil pan-valve cover-side cover-intake-exaust gaskets. They also installed a brand new Carter YF carburator, a new clutch and flywheel, they rebuilt the clutch master cylinder, they installed a brand new distributor-cap-and rotor, brand new fuel pump with integral filter, inline fuel filter, and cleaned the fuel tank. And lastly a brand new starter motor and battery. The outside was stripped with a soda blaster about 98% there is a little paint left here and there but its pretty well cleaned off. I get tons of compliments on the "look" thats kinda why I never finsihed the polishing. It drives pretty good for the age and is a blast with the doors open. I had to stop the shops progress due to fundage difficulties, the remaining things the truck needs are some minor brake work (it pulls to the right a bit) and tires(the originals are dryrotted but hold air great!), and the carb needs fine tuned(they said its running rich how it is?) It would make an awsome rat rod, country cruiser, or lunch wagon. Construction vehicle? Advertising? The truck is inspected until 4/14 and I have a clean PA title in my name that can be transfered to the new owner. For a fee I would be comfortable to drive this truck a few hours away, If your going much further you might want to trailer it or arrange shipping. If you have any questions about the truck or want more pictures please don't bid until your satisfied. Buyer is responisble for shipping this vehicle, it is sold as is with no warranty.On Jul-01-13 at 15:15:13 PDT, seller added the following information: Selling my most favored vehicle ever...... 1970 P350 Aluminum Step Van 4.9L 300ci I6 All aluminum body will never rust! I had this truck for about two years now, I have probably put 500 miles on it. All the doors and locks work great, windows wind down good but are stiff going up. The body is very straight, with only a small bondo spot on the front corners (thats the pink in the pictures)Transmisison is a 4speed manual, the first is really low. It does around 60mph on the highway though! Shortly after I bought it I had a local garage install the engine from a late 80's ford f150, it has around 80,000 original miles, it has new oil pan-valve cover-side cover-intake-exaust gaskets. They also installed a brand new Carter YF carburator, a new clutch and flywheel, they rebuilt the clutch master cylinder, they installed a brand new distributor-cap-and rotor, brand new fuel pump with integral filter, inline fuel filter, and cleaned the fuel tank. And lastly a brand new starter motor and battery. The outside was stripped with a soda blaster about 98% there is a little paint left here and there but its pretty well cleaned off. I get tons of compliments on the "look" thats kinda why I never finsihed the polishing. It drives pretty good for the age and is a blast with the doors open. I had to stop the shops progress due to fundage difficulties, the remaining things the truck needs are some minor brake work (it pulls to the right a bit) and tires(the originals are dryrotted but hold air great!), and the carb needs fine tuned(they said its running rich how it is?) It would make an awsome rat rod, country cruiser, or lunch wagon. Construction vehicle? Advertising? The truck is inspected until 4/14 and I have a clean PA title in my name that can be transfered to the new owner. For a fee I would be comfortable to drive this truck a few hours away, If your going much further you might want to trailer it or arrange shipping. If you have any questions about the truck or want more pictures please don't bid until your satisfied. REVISION:7/1/13: I added pictures of the undercarriage, its in pretty darn nice shape. Aluminum floor sits on aluminum rails that sit on wood thats on steel frame rails. Good desighn doesn't promote rust/rot. Dimensions are as follows: Bumper to bumper is about 15',Outside Hight is about 9', Inside cargo hight is 6'1" tall, inside cargo width is 6'10"wide, inside cargo length is 8'long. AGAIN I AM HAPPY TO ANSWER ANY QUESTIONS AND CAN SEND PICS AS NEEDED. THANKS, JON