1996 Chevrolet Tahoe

Sport Utility

5.7L 350Cu. In. V8 GAS OHV Naturally Aspirated

Automatic

3GNEC18R9TG151027

Clear

GAS

I have my very well cared for and hard to find 1996 Tahoe 2dr 2wd custom show truck for sale. Truck use to be bagged on 22" billet specialties wheels. The pictures are for reference only and the truck will be sold the way it is in the title picture. This one has been a project with no expense spared. It has a ton of mods so I will start off with all the modifications. Body - custom 08 Red paint, 2004 front clip, shaved upper body line, shaved doors, shaved gas lid, shaved rear doors with recessed license plate box, weld in roll pan, gas fill relocated to driver rear a pillar, custom one off metal front bumper with air dam ( narrowed and tucked under). Brand new barn door windows and brand new windshield and brand new passenger side cargo window. Suspension - Truck was previously air bagged. Currently has 22" wheels with 265/35/22. Still has 4 link installed in rear with coil mounts and new lowered coil springs and new shocks, front has 2" drop springs along with 2" drop spindles and adjustable upper control arms. Truck sits with a 4/6 drop. Also the dip in the frame that Chevy puts on the tahoes just in front of the rear tires has been removed and boxed in so that it can lay out even front and rear and rear end has been narrowed 2.5" each side with moser axles, drilled and slotted rotors up front. Engine - has brand new MPI injection set up, intake manifold gasket was recently replaced with metal core felpro gasket, 10 gallon fuel cell mounted between frame rails behind rear end, vacuum lines replaced, custom air intake installed, truck has a custom true dual exhaust, new fuel pump, new coils, new plugs and wires and cap/rotor, has a high output 250 amp alternator with all 0 gauge stinger wire from alt to batter that is relocated to the passenger rear cargo area, all grounds are also 0 gauge stinger so the big 3 has been done as well. Interior - Custom slicked out and painted dash to match exterior, billet specialities steering wheel, new seats just recovered, front seats out of 99 escalade and rear seats are a 3rd row Tahoe seat that fits between the rear tubs, has new carpet installed in front/rear passenger area, center console, doors panels covered to match seats, the rear cargo area was raised 8" and completely boxed out with square tubing and covered in sheet metal, extra wide tubs installed, LED tail lights that mount in rear windows, AVS shaved door kit. The below is a list of remaining things to be done to the truck Body - front bumper needs to be adjusted and final bolted to frame. Currently bolted snug with 1 bolt on each frame mount, air dam installed, driver fender needs minor adjustment to even door gap, a wiper cowl will need to be made/purchased, there is a small scratch below passenger door from loading it on car trailer and the door pins in the rear along with one small chip can be touched up, window wiper motor was taken out when painting the firewall just needs to be reinstalled. Suspension - Only needs an alignment, breaks bleed and if wanted 2" adapters in rear to bring out the wheels to stock location. Engine - Just recently tuned up and oil changed. I have a billet overflow tank for the radiator that will need to be installed along with either install the stock fan shroud or go with an electric fan. Truck has only been drive. 5 miles since the tear down in 07 but has been cracked up and ran every week to keep battery charged. The ac condensor was disconnected for front end swap and needs ro be recharged. It has not exhibited any issues for drivability. Interior - needs new seat belts, center console back installed, I have billet air vent they just need to be installed, I have chrome interior door handles that need to be installed and then the handles and door latch connected with a cable, door panel need to be bolted to doors, I will give the buyer a set of brand new Alpine Type S components for the doors just need to get them installed, interior panels need to be painted and installed, front passenger a-pillar needs to be replaced and I cant think of anything missing off hand besides seat belts but I have not laid everything in its exact location tho big trim pieces I do have, I would say I have 95% of the interior if anything is missing its small and cheap, the rear of th back seats need to be bolted to the floor, the rear cargo area is all sheet metal and there are 8-3/4" holes where the tank lines where ran, LED tail lights were removed to modify trim panel and they need to be reinstalled but they are still connected and work perfect, the headliner will need to be made black to match and installed, the glove box is painted to match dash but needs the guts so that it can be installed. This truck has a ton of man hours and money spent on it. Unfortunately I have ran out of both in trying to finish it. With little time and money this truck can be featured in a mag. Truck truly is amazing and needs little work/money it only small items that it needs. I have tried to show the good / bad of the truck the best that I can. If you have any questions please email me. I will post more pics tonight.