2003 Ford Mustang

Coupe

4.6L 281Cu. In. V8 GAS DOHC Naturally Aspirated

Automatic

1FAFP42R23F454265

Clear

Gasoline

Well here is the story, I have (3) 03 Mach1 Autos. My first is a Torch Red that I have had since 04. It is on it’s second renovation. The TR car has 23k on it and I pulled the motor to put in a big bore stroker motor. My intention was to use this motor in a good roller or cheap Mach with a bad motor for my daughter. I found the car in this listing and purchased it off ebay, when I went to pick it up it was rougher than I expected but I took it anyway. I got the car home and proceeded to strip it down to replace everything on this car with parts of my TR. I wanted to give my daughter a car for Christmas and happened to find number 3. This car is a DSG Mach with 4600 miles on it and she absolutely loves it. Therefore I now have no need for the Azure Blue car. In addition I have two other Mustangs, this car needs to go. So far I have stripped the body down, I had it on a rotisserie to media blast the undercarriage. I coated it with black POR15 and topped it with Eastwood Chassis Black. Every nut, bolt and part was blasted coated and painted as well as the rear end, k member, all suspension parts etc. The car now is back to rolling status, has new rotors, pads, stainless brake lines, Eibach springs and the rear was just rebuilt. I have over $1500 in the rear alone, new Ford Racing 4:10s and carrier and cover, Moser 31 spline axles and extended studs. The body does have some bumps and bruises but I have all the parts to put it back together including an 01 Cobra front bumper cover with fogs and bezels. In additions to the roller I have the following parts that will be offered up to the buyer, but only if the roller sells. If I can’t sell the roller I need all parts to finish building it. 2 radiators with fans 2 sets of Mach1 wheels and tires, assume tires are shot Trunk lid off the TR Mach Auto Tranny and TC from the AB Mach 2 Motor the first motor is the one out of the AB. It has 63k on it and is torn down to the shortblock. The previous owner tried to diagnose an engine issue with the motor in the car and couldn’t get the valve covers off. I pulled the motor and the issue was a chain guide on the passenger side. The plastic part broke loose and the chain was slapping the aluminum guide. No parts got into the bottom end, shortblock looks fine as well as the heads. The second motor is out of the TR Mach and has roughly 23k on it, this motor has a few mods. Ported and Polished intake, 3/8 “ Intake Spacer, Aeromotive fuel rails, Meziere electric water pump, Bassani mid length headers. This motor is complete top to bottom and is ready to go. 2 Master cylinders TR k member and A arms Extra set of bumpers Extra set of seat belts 2 stock differential covers Kenny Brown K Member Brace Kenny Brown Trac Bar Kenny Brown Caster Camber Plates Kenny Brown 3 Pt Strut Tower Brace American Racing Stainless X Pipe Steeda Stainless Radiator Cover 2 Stock TBs Mafia AutoMeter Parts Lunar Guage Cluster Lunar Boost, Fuel, Oil, Water, Wideband, Trans Temp A pillar 3 guage Pod 2 Single guage pods for steering column, one black plastic, one carbon fiber Cluster 2 guage pod Canton aluminum Power Steering Tank Canton Aluminum Coolant Tank 2 sets factory coil on plugs Extra set of Airbags ScottRodFab aluminum Engine Bay Panels Carbon Fiber Valve Covers 2 alternators Teksid Block 3:73 Factory Gears A large 4’x4’x4’ box full of parts off the TROn Apr-25-13 at 17:16:43 PDT, seller added the following information: To clarify what is included in the listing. The "Roller" includes what is in the pics, car body, suspension, rearend, stock tires and wheels, and body work to complete the car including front bumper, rear bumper, 01 Cobra front bumper cover, rear bumper cover, both front fenders, hood, shaker set up and rockers. I believe I have all bodywork to complete the roller. It will definately need some bodywork and a paint job. The interior is 100% complete, it is however dirty as hell and has the usual drivers side bolster wear. (AKA Tear) All the parts that are listed will be offered up first to the buyer of the roller, if the roller doesn't sell don't ask me to sell parts, I will need them. I also have a couple locals interested and if I get a good offer the auction is over unless it picks up. I want this stuff out of my garage ASAPOn Apr-26-13 at 18:12:46 PDT, seller added the following information: Note: The motor in the picture is NOT included in the auction but is available at the end of the auction.